MapleSim Hydraulics Library from Modelon - MapleSim Help

Online Help

All Products    Maple    MapleSim


Home : Support : Online Help : MapleSim Toolboxes : MapleSim Hydraulics Library from Modelon : Cylinders : ModelonHydraulics/Cylinders/DoubleActingDualRod

MapleSim Hydraulics Library from Modelon

Double Acting Dual Rod  A double acting cylinder with rods on both sides

This model is a double acting cylinder with rods on both sides and damping at the ends modeled with springs and dampers. The model has two active chambers and external leakage at both sides. External leakage can be turned off by clearing the hasExternalLeakage setting (found under the Inspector tab in the Parameters   Leakage section).

Cylinder Geometry This is a simplified overview of the geometric parameters defining the cylinder geometry:

Mechanical Friction This model includes Stribeck Friction (see the following figure).

Connections

Name

Description

Modelica ID

portA

Port A, where oil flows into the component (positive q, port_A.p > chamberA.p means positive dp)

port_A

portB

Port B, where oil flows into the component (positive q, port_B.p > chamberB.p means positive dp)

port_B

flangeb

Piston rod mounting point b

flange_b

mount

Cylinder housing mounting point

mount

flangea

Piston rod mounting point a

flange_a

Parameters

General Parameters

Name

Default

Units

Description

Modelica ID

roda

12

m

Length of rod, side a

RodLength_a

rodb

12

m

Length of rod, side b

RodLength_b

housing

2

m

Length of housing

HousingLength

piston

0.05

m

Length of piston

PistonLength

mpiston

100

kg

Effective mass of piston and rigidly coupled masses

PistonMass

cA

108

Nm

Stiffness of stop at stroke end A

c_A

dA

106

Nsm

Damping of stop at stroke end A

d_A

cB

108

Nm

Stiffness of stop at stroke end B

c_B

dB

106

Nsm

Damping of stop at stroke end B

d_B

ApistonA

0.001

m2

Effective area of left side of piston

piston_areaA

ApistonB

0.001

m2

Effective area of right side of piston

piston_areaB

VdeadA

0.001

m3

Dead volume of chamber if piston is at left end of housing (side A: stroke = 0)

dead_volumeA

VdeadB

0.001

m3

Dead volume of chamber if piston is at right end of housing (side B: stroke = max)

dead_volumeB

kp

0

 

Pressure damping coefficient

kp

ΔTsystem

0

K

Temperature offset from system temperature

dT_system

reverse

false

 

Reverse the positive flow in the component

reverse

Friction Parameters

Name

Default

Units

Description

Modelica ID

fbreakaway

100

N

 

breakaway_friction

fmixed

10

N

 

mixed_friction

vfmixed

110

ms

 

mixed_friction_velocity

dviscous

2.5·103

Nsm

 

viscous_damping

tabular

false

 

If true, use tabular models, else an analytic one

Tabular

fpos

0.,1.

 

[v, f] Positive sliding friction characteristic (v>=0)

f_pos

Initialization Parameters

Name

Default

Units

Description

Modelica ID

InitialStrokeA

[1]

m

Initial stroke of cylinder chamber A, default is middle position

InitialStroke_A

[1] 12housing12piston

Leakage Parameters

Name

Default

Units

Description

Modelica ID

has external leakage

true

 

If true, external leakage at rod seal is included

hasExternalLeakage

GextB

4.2·10-13

m3sPa

Hydraulic conductance for external leakage, rod B

G_ext_B

GextA

4.2·10-13

m3sPa

Hydraulic conductance for external leakage, rod A

G_ext_A

Gleakint

0

m3sPa

Hydraulic conductance G=∂q∂p

G_intLeak

See Also

Cylinders, MapleSim Hydraulics Library from Modelon Overview


Download Help Document

Was this information helpful?



Please add your Comment (Optional)
E-mail Address (Optional)
What is ? This question helps us to combat spam